Working With Wood: What You Should Know

Woodworking can be a lot of fun, but many people get discouraged because they are not knowledgeable enough on the subject and feel that creating nice pieces is a little overwhelming. Woodworking is all about creativity, so this article is going to discuss a few things that help bring your creative side to the surface. Don’t let woodworking frustrate you, but instead get ready to make some art!

Take care when using power tools. If you are new to woodworking, be very careful when you are operating power tools for the first time. Read the manual thoroughly, and if possible, have someone with experience demonstrate how to use it properly. This will ensure that you don’t have a nasty accident during your woodworking project.

Take the time to plan out your woodworking project step-by-step before you even begin. Doing this will help to ensure that you are going to get the results that you are looking for. If you do not plan ahead it is likely that you will make an error that could ruin the entire project.

Be safe when you first start out in woodworking. Wear the proper safety clothing, including goggles. You may feel silly, but you are dealing with sharp tools and splintering wood. These are things that can cause significant injuries to even the most seasoned woodworker. So be safe, and make sure all that are around you are safe too.

Stir, never shake stains and finishes before use. Over time, these settle, so mixing is necessary. Shaking, however, adds bubbles and doesn’t always mix the stain or finish thoroughly. Stirring mixes the products better by evenly mixing in any settlement that occurred during storage. Stains and finishes that are not mixed thoroughly will not apply correctly to the wood you’re staining and are at risk of looking blotchy.

It’s very important to always make sure that the saw blade you use is in great condition every time you use it. A dull blade can’t efficiently get the job done. It can also create errors with the wood that can be quite costly.

If you have any pockets on the shirt you are wearing, remove everything from them before you start working with a table saw. It is very common for objects like pens and rulers to fall from your pocket and get caught in the blade, which can lead to some pretty serious injuries.

Make sure the lighting is sufficient in your work area. Accuracy in woodworking means you need to see well. Additionally, you’ll be using sharp instruments to cut the wood. You must have good vision when woodworking, or you may be injured.

Make accurate lines and measurements by using a drafting square instead of a drywall square, yardstick or ruler. Drafting squares are smaller and easier to manage and are much more accurate than any of these tools. This is a handy tool to keep at your side because it is smaller. Additionally, drafting squares are very affordable, selling for about five bucks at any art supply store.

Quickly get rid of burn marks caused by the router. Certain woods burn easily when routered and it can be very time-consuming trying to sand the marks away. If the router template is complex, it may be nearly impossible. Try just routering down further just a small amount using the same bit. About 1/32nd of an inch should take the burn marks off.

Every good woodworking shop needs a quality combination square. It is needed for almost every job you’ll tackle. It makes a good depth gauge, using the straight side. It is, of course, perfect for miter cuts. Most have a level built right in. A good combination square is a must-have tool, right up there with a hammer and drill.

When you are getting ready to glue wood together, get some packing tape ready to help you secure the wood. Packing tape is a great way to tighten up those joints so that the glue sets as perfectly as possible. Pre-cut the packing tape so that you have it handy the minute you need it.

When using a new power tool, always be sure to completely read the users manual. Ignorance can be a very painful thing when it comes to power tools, not to mention the expense and the mess that can occur if something goes wrong. Safety always comes first when it comes to working with power tools.

Test a new woodworking technique on a piece of scrap wood. This will help you to think out a new cut, stain, or tool on a medium that is less valuable to you. Anything done to scrap wood does not matter. It is not always best to experiment with unfamiliar processes on the final piece.

Prior to putting your saw into any piece of wood, inspect it to ensure that there are not any screws or nails in the area you are going to cut. This may seem unnecessary if you have new lumber, but it can stop an accident from occurring. Staples are another thing that you will want to look out for.

All wood should be stored in a cool dry location. If the wood is allowed to draw moisture, the wood will expand and contract as the wood dries out. To help prevent this keep wood off the floor and stack to allow proper air circulation around each piece of wood.

Think of how you will use your shop when setting up your working space. Don’t get it stuffed with a bunch of equipment that you can’t easily move around. Your machines should have a lot of room between them. This is a very important factor when designing your shop. You’ll be more productive and the shop will be safer.

After having read through these helpful tips, are you ready to embrace woodworking and start creating things? It is so much fun, and it is so relaxing. Take your time and enjoy yourself. Woodworking is all about the experience, and you get better as you go along. See what you can make today.